Duet Tub Door & QWALL-TUB Kit Tub Door AND SHOWER BACKWALLS KIT INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to al
PLEASE NOTE: • On the outside Glass door (A) the Handle and the Rollers should face out. • On the inside Glass door (B) the Handle and the Rollers
9. One by one suspend both Glass doors onto the Upper guide rail as shown on Fig.13. Tilt the Glass door (A) a little to make the glass slide into t
10. Slide both Glass Doors to the right. Insert the Left guide block (13) into the channel on the left side of the Guide rail and secure it using th
12. Fasten the Rubber stopper (14) inside the groove of the Wall profile using the Round head screw ST4.2×16 (08). See Fig. 17 for details.
14. Apply the sealant along the profiles and guide rails; on the seams between the bottom guide rail and the profiles as well as along the shower ba
QWALL TUB TUB ACRYLIC BACK WALL INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any tim
Preparation 1. After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are included in the packag
Detailed Diagram of Tub Back Wall Components 12437589106 Packing List 01 Side panel 2pcs 06 Wall anchor 21pcs 02 Back panel 2pcs 07 Countersunk
Back Panel Installation Instruction 1. Measure the distance of the back wall of the tub (corner to corner) The distance is “W” See Fig. 1 for det
3. Measure the side walls from the corner to the front point where the Side panel (01) is going to end. This distance is “D”. See Fig. 3 for deta
DUET SHOWER DOOR INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time without prior
Fig. 5 5. Attach the Center cover (05) vertically at the center point along the line and mark the drilling holes throu
Fig. 7 6. Attach the Corner cover (04) to the corner of the wall and mark the drilling holes through the predrilled hole
Fig. 9 7. Determine the position of both Back panels (02). NOTE: a) Narrow side of the Back panel cannot be trimmed and
8. Place the Back panel (02) on a flat piece of plywood or a particle board. Cut the side end of the Back panel by making a few deep scratches with
9. Mount the Center cover (05) to the center of the back wall using the Countersunk screws ST4.2×30 (07). Do not tighten the screws. Leave the Cent
11. Slide the right edge of the left Back panel (02) all the way behind the Center cover (05) and push the Back panel against the wall. You can adju
13. Align both Back panels at the top and tighten the screws on the Center cover (05) to secure this assembly in place. See Fig. 17 and Fig. 18 for
14. Determine the position of both Side panels (01). NOTE: a) Narrow side of the Side panel cannot be trimmed and should face the corner of the s
Fig. 21 16. Place the marks on the Side panel (01) which is going to the side wall with the fixtures according to the t
Fig. 23 17. Apply the sealant to the back surface of the Side panel (01). Apply the sealant around the drilled holes a
Preparation 1. After opening all boxes and packages, read this introduction carefully. Check that all of the needed parts are included in the packag
18. Slide the edge of the Side panel (01) all the way behind the Corner cover (04) and push the Side panel against the wall. Align the top of the Sid
19. Apply the sealant to the back surface of the Side panel (01) for another side wall installation. See Fig. 27 for details.
Fig. 29 21. Fasten tight the Corner covers (04) and the Center cover (05) to secure the Side panels (01) and the Back p
22. Use decorative plugs to cover the screw holes in the Corner covers (04) and the Center cover (05). See Fig. 29 for details.
Tub Glass Shelves Installation Instruction 24. Find the desirable height for the Glass shelves (09) and mark the locations on the wall. NOTE: The G
Rev 1.1 21 10. Mount the Glass brackets (10) to the wall using the Countersunk screws ST4.2×30. NOTE: padded set screw of the Glass bracket should be
Rev 1.1 22 Product maintenance To insure long lasting life for your acrylic back walls, wipe them off after each use with a soft cloth. To clean the
DREAMLINE™EXCLUSIVELIMITEDWARRANTYASOFMAY6,2013Thiswarrantyextendsonlytotheoriginalowner/end‐userforhouseholduse onlyandisn
TEL: 866-731-8378 – 215-957-1411 FAX: 866-227-9245 – 215-893-1780 WWW.BATHAUTHORITY.COM Rev 1.1 24For more infor
Detailed Diagram of Shower Door Components 1234678910111213145 Packing List 01 Upper guide rail 1pc 08 Round head screw ST4.2×16 16pcs 02 Wa
Shower Door Installation 1. Measure the distance between two walls. This distance is marked as “W”. See Fig. 1 for details. F
3. Secure Upper guide rail (01) and Bottom guide rail (04) to the Glass profiles (03) with the Flat head screws ST4.2x25 (09). See Fig. 3 and Fig.
4. Push the Wall profiles (02) all the way over the Glass profiles (03) at both sides. Make sure the flange of the wall profile faces inside the sho
5. Move the finished frame to the designated position and push it against the walls. If your top and bottom wall opening measurements are different
7. Apply silicone along the wall profile and around the holes on the wall. Also apply silicone under the bottom guide rail. Place the shower frame b
Kommentare zu diesen Handbüchern