MODEL: __________ STYLE: __________ SELECTOR: __________ Please choose your door model, style and selector according to your order for e
“Elegance” Rev.4 Ver.1 07/2013 10 8. Open the Glass door (03). See Fig. 8 for details. Fig. 8 9. Close the hole in the
“Elegance” Rev.4 Ver.1 07/2013 11 10. Push the Anti-water strip (10) into the vertical groove of the Glass profile for glass door (02). Attach the Bot
“Elegance” Rev.4 Ver.1 07/2013 12 ATTENTION: Steps 11-16 Follow these steps if the width of your door is less than 37¾” and you are installing the do
“Elegance” Rev.4 Ver.1 07/2013 13 12. Use a level to ensure that the Glass door (03) and the Wall profile (05) is absolutely vertical. Draw a line alo
“Elegance” Rev.4 Ver.1 07/2013 14 14. Adjust the width of the Glass door (03) by pulling out the Glass profiles (02) and (04) if it necessary for size
“Elegance” Rev.4 Ver.1 07/2013 15 16. Apply silicone sealant between the tray or threshold and the pivot bracket. Also, apply silicone between the wa
“Elegance” Rev.4 Ver.1 07/2013 16Style “B”: Stationary Glass Assembly and Installation NOTE: Use parts from Diagram “B” and “C” for the Stationar
“Elegance” Rev.4 Ver.1 07/2013 17 19. Draw a line along the inner edge of the Wall profile (05) on the wall. Detach the Wall profile from the Stationa
“Elegance” Rev.4 Ver.1 07/2013 18 21. Adjust the Stationary glass (21) position to ensure that when the Glass door (03) is closed, there is a gap (1/1
“Elegance” Rev.4 Ver.1 07/2013 19 23. Apply silicone sealant between the tray or threshold and the pivot bracket. Also, apply silicone between the wal
“Elegance” Rev.4 Ver.1 07/2013 2 Preparation 1. After opening all boxes and packages, read this introduction carefully. Check that all of the need
“Elegance” Rev.4 Ver.1 07/2013 20Style “B” and “D”: Stationary Glass Assembly and Installation NOTE: Use parts from Diagram “B” or “C” (depends on y
“Elegance” Rev.4 Ver.1 07/2013 21Style “C” and “D”: Shower Enclosure Assembly and Installation NOTE: Use parts from Diagram “A” and Diagram “B” or “
“Elegance” Rev.4 Ver.1 07/2013 22 26. Apply clear silicone along the inner channel of the Glass profile (04) and push the Stationary glass (21) insid
“Elegance” Rev.4 Ver.1 07/2013 23 28. Push the Pivot retainers (08) into both ends of the Wall profile for glass door (01). See fig. 30
“Elegance” Rev.4 Ver.1 07/2013 24
“Elegance” Rev.4 Ver.1 07/2013 25NOTICE: The Glass door has 2 cuts for the Pivot assemblies. The deeper cut must be on the top. 32. Remove the Bolts
“Elegance” Rev.4 Ver.1 07/2013 26 34. Press the Anti-water strip (29) onto the vertical edge of the Stationary glass (21). Carefully butt the Stationa
“Elegance” Rev.4 Ver.1 07/2013 27
“Elegance” Rev.4 Ver.1 07/2013 28 37. Adjust the width of the opening section of the Glass door (03) by loosen the holding screws on the Pivot assemb
“Elegance” Rev.4 Ver.1 07/2013 29 39. Do the final adjustment if necessary. Make sure the Glass door (03) closes tight to the Anti-Water strip (29).
“Elegance” Rev.4 Ver.1 07/2013 3Detailed Diagrams of Shower Door Components Diagram A
“Elegance” Rev.4 Ver.1 07/2013 30 41. Apply silicone sealant between the tray or threshold, the stationary glass and the accessory. Also, apply silico
“Elegance” Rev.4 Ver.1 07/2013 31 Style “C”: Support Bar Assembly and Installation NOTE: Use parts from Diagram “C” for the Support Bar assembly a
“Elegance” Rev.4 Ver.1 07/2013 32 Style “D”: Glass Shelves Assembly and Installation NOTE: Use parts from Diagram “B” for the Glass Shelves assemb
“Elegance” Rev.4 Ver.1 07/2013 33 Maintenance To insure long lasting life for your acrylic back walls, wipe them off after each use with a soft cl
DREAMLINE™EXCLUSIVELIMITEDWARRANTYASOFMAY6,2013Thiswarrantyextendsonlytotheoriginalowner/end‐userforhouseholduseonlyandisnottr
TEL: 866-731-2244 FAX: 866-227-1533 WWW.BATHAUTHORITY.COM For more information on DreamLineTM Shower Doors and Enclosure please vi
“Elegance” Rev.4 Ver.1 07/2013 4 NOTE: Unpack your unit carefully and inspect it. Lay it out and identify all parts using the detailed diagram and p
“Elegance” Rev.4 Ver.1 07/2013 5 Self Closing Pivot Assembly Parts List A Flat head bolt M4×8 1pc G Bolt M12×10 1pc B Pivot bracket 1pc H
“Elegance” Rev.4 Ver.1 07/2013 6Style “A”: Single Shower Door Assembly and Installation NOTE: Use parts from Diagram “A” for the Single Shower doo
“Elegance” Rev.4 Ver.1 07/2013 7 2. Push the Pivot retainers (08) into both ends of the Wall profile for glass door (01). See Fig. 2 for details.
“Elegance” Rev.4 Ver.1 07/2013 8 4. Attach the Pivot assembly (07) to the top and the bottom ends of the Glass profile for glass door (02) with the F
“Elegance” Rev.4 Ver.1 07/2013 9 NOTICE: The Glass door has 2 cuts for the Pivot assemblies. The deeper cut must be on the top. 6. Remove the Bolts
Kommentare zu diesen Handbüchern