DreamLine DL-6714-01CL Installationsanleitung

Shower Enclosure and Shower Base Kit Installation Instruction IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products

“FLEX” Enclosure Rev.1, Ver.3 03/2014 9 7. Slide the Return glass panel (09) assembly into the groove of the Return w

“FLEX” Enclosure Rev.1, Ver.3 03/2014 10 8. Extend width of the Door assembly (02) by stretching the top and bottom Expanding rails toward th

“FLEX” Enclosure Rev.1, Ver.3 03/2014 11 9. Make sure the Door assembly (02) is fully extended inside the Wall profile (01) and the Corner pr

“FLEX” Enclosure Rev.1, Ver.3 03/2014 12 11. Do the final adjustments to the Door assembly (02) and Return glass panel (09) if required. Open

“FLEX” Enclosure Rev.1, Ver.3 03/2014 13 13. Attach Flanged Anti-water strip (07) to the vertical edge of the Stationary glass. Cut Bottom A

“FLEX” Enclosure Rev.1, Ver.3 03/2014 14 Product Maintenance To ensure long lasting life for your acrylic back walls, wipe them off afte

SLIMLINE SHOWER BASE SHOWER BASE DIMENSIONS AND INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 2Preparation 1. Examine boxes and packages for shipping damage. Carefully remove Shower base from th

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 3SINGLE THRESHOLD SHOWER BASE Center Drain Configuration MODEL SPECIFICATION D (in) W (in)

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 4Left-Hand Drain Configuration MODEL SPECIFICAT

FLEX SHOWER ENCLOSURE INSTALLATION INSTRUCTIONS IMPORTANT DreamLineTM reserves the right to alter, modify or redesign products at any time with

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 5Right-Hand Drain Configuration

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 6NEO SHOWER BASE MODEL SPECIFICATION W (in) A (in) B (in) C (in) DLT-2

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 7QUARTER ROUND SHOWER BASE MODEL SPECIFICATION W (in) C (

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 8DOUBLE THRESHOLD SHOWER BASE Corner Drain Configuration MODEL SPECIFICATION W (in) C

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 9Left-Hand Drain Configuration MODEL SPECIFICATION D (in) W (in) D1 (in) W1 (in)

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 10Right-Hand Drain Configuration MODEL SPECIFICATION D (in) W (in) D1 (in)

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 11Diagram of the Shower Base in a Cross Section Finished Wall Cement board S

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 12Shower Base Installation Preparation 1. Ensure that the floor and the studs are at right angle. Pr

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 132. Install the shower drain (NOT PROVIDED) according to the drain installation manual (supplied wit

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 14 4. Level the tray and place marks on the studs above the upper edge of the tile flange. See

“FLEX” Enclosure Rev.1, Ver.3 03/2014 2Preparation 1. After opening all boxes and packages, read this introduction carefully. Check that al

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 15 6. After the bedding material has been poured and before it sets, place the shower base into the p

“SLIMLINE SHOWER BASE” Rev.3 Ver.5 07/2013 16 Fig. 9 Product maintenance To insure long lasting life

DREAMLINE™EXCLUSIVELIMITEDWARRANTYASOFMAY6,2013Thiswarrantyextendsonlytotheoriginalowner/end‐userforhouseholduseonlyandisnottr

TEL: 866-731-2244 FAX: 866-227-1533 WWW.BATHAUTHORITY.COM For more information on DreamLineTM Shower Doors please visit www.Bath

“FLEX” Enclosure Rev.1, Ver.3 03/2014 3Detailed Diagram of Shower Enclosure Components 345678213911011 Door packing List 01 Wall profile 2pc

“FLEX” Enclosure Rev.1, Ver.3 03/2014 4Door Assembly Diagram Alluminum profileExpandable railExpandable railGlass doorStationary glassAllumin

“FLEX” Enclosure Rev.1, Ver.3 03/2014 5Shower Enclosure Installation NOTE: The installation of this shower enclosure requires two installers.

“FLEX” Enclosure Rev.1, Ver.3 03/2014 6 3. Trace the drilling holes on the wall through the predrilled holes in the Wall profile (01). Drill

“FLEX” Enclosure Rev.1, Ver.3 03/2014 7 5. Slide the Corner profile (10) over the aluminum vertical edge of the Re

“FLEX” Enclosure Rev.1, Ver.3 03/2014 8 6. Install the Handle (13) onto the Door assembly (02). Move the Door assembl